Feeding, Starvation and Food Stores

Visual problem library

Feeding, Starvation and Food Stores

Compare the photographs, then open the guide that matches your observation. A picture is a clue, not a confirmed diagnosis.

Compare what you see, then open the matching guide for inspection checks and a practical next step.

Photographs are clues, not a diagnosis.

Compare several frames, colony history and test results. For suspected foulbrood, stop moving comb between colonies and contact your state apiary inspector.

Jump to a specific problem

Insufficient honey stores before a shortage

Light boxes, little capped food and repeated consumption without incoming nectar.

Act promptly while feeding is still practical

Food needs depend on colony size, weather, forage and hive system. A universal frame count does not fit every winter.

Compare additional reference photographs

Compare where food is located relative to the bees. An external appearance or a single photograph cannot measure total usable reserves. Open The BeeMD reference for starvation (new tab).

Recognize the signs

Light boxes, little capped food and repeated consumption without incoming nectar.

What else can look similar?

A heavy hive may contain equipment weight rather than food; capped brood is not stored honey.

Inspect and confirm

Use a veil, hive tool, notes and a consistent weight or heft comparison. In suitable conditions count food areas on both frame faces and their position relative to bees.

Your next step

Keep enough stores for the colony rather than planning another harvest.

Take action

  1. Keep enough stores for the colony rather than planning another harvest.
  2. Ask a local mentor for a seasonal reserve target for your specific configuration.
  3. Feed suitably while temperatures permit uptake and processing; switch to an appropriate accessible emergency method if weather closes that option.

Avoid this mistake

Do not use one national weight target blindly or leave feed in honey intended for sale.

Causes, prevention and follow-up

Common causes

Poor flows, late starts, many mouths, excessive harvest or a long winter.

Check the result

Check uptake and changing reserves at short intervals until adequate, then keep monitoring. A colony refusing feed needs a feeder, weather and health check.

Prevent it happening again

Record baseline hive weight and food use through the year; reassess after harvest.

When to get help

Ask for local help if winter approaches with inadequate reserves.

Supplies and their limits

A hive top feeder provides internal feed access. Choose the actual 8 or 10 frame width, use all floats and required parts, test for leaks and follow cleaning instructions. It does not cure disease and liquid uptake depends on weather. Use an existing sound compatible feeder when possible. Remove sale honey supers from the feeding plan.

Little LaRue supplies use our own checkout.

View Little LaRue hive top feeders
Sources and review notes

Reviewed November 19, 2026. Adapt timing to local climate, weather and colony condition. A photograph or symptom list does not confirm a diagnosis.

Pollen shortage and poor protein supply

Little stored pollen near brood, reduced larval feeding or stalled buildup over time.

Monitor brood and stores; intervene when evidence supports it

Pollen supplies protein for raising young bees. Bee bread is pollen stored and processed in comb. Low incoming pollen on one day does not prove a shortage.

View the pollen shortage and poor protein supply reference photo above.

Recognize the signs

Little stored pollen near brood, reduced larval feeding or stalled buildup over time.

What else can look similar?

Queen trouble and brood disease also reduce brood. Color alone does not establish the quality or source of pollen.

Inspect and confirm

With a veil and light, inspect the bands beside brood for pollen and larvae. Record several days of weather and forage rather than judging a single quiet afternoon.

Your next step

Confirm adequate carbohydrate food first.

Take action

  1. Confirm adequate carbohydrate food first.
  2. Discuss a bee specific protein supplement with a local mentor if brood demand and lack of pollen justify it.
  3. Offer only amounts the colony can use and monitor for beetle or spoilage problems; improve future forage where practical.

Avoid this mistake

Do not feed random flour, feed so much that pests breed in leftovers, or assume a patty treats disease.

Causes, prevention and follow-up

Common causes

Limited flowering plants, bad flight weather, drought or colony demand exceeding forage.

Check the result

Check acceptance and larval condition within several days; remove spoiled leftovers. Persistent poor brood despite food needs diagnosis.

Prevent it happening again

Support varied local forage and avoid starting brood growth without enough food for resulting bees.

When to get help

Seek help when larvae are discolored or the colony continues to dwindle.

Supplies and their limits

No verified protein supplement link is offered. Local forage and a mentor’s food assessment may avoid an unnecessary purchase.

Sources and review notes

Reviewed November 19, 2026. Adapt timing to local climate, weather and colony condition. A photograph or symptom list does not confirm a diagnosis.

Nectar dearth, a gap in incoming nectar

Falling hive weight, less fresh nectar, defensive behavior or interest in spills.

Monitor stores closely and prevent robbing

A nectar dearth means flowers are supplying little usable nectar. Bees may still fly intensely while reserves decline.

Compare additional reference photographs

The examples illustrate forage shortage and changes around the colony. Confirm incoming food and stored reserves in your own hive; flower appearance alone does not measure nectar supply. Open The BeeMD reference for dearth (new tab).

Recognize the signs

Falling hive weight, less fresh nectar, defensive behavior or interest in spills.

What else can look similar?

A quiet entrance can also reflect cold, queen problems or a weak population. Flying activity alone does not measure food.

Inspect and confirm

Use food and weight records, local bloom observations and a brief inspection when suitable. Look for fresh shiny nectar, stored honey and brood demand.

Your next step

Stop unnecessary harvest and exposed feeding.

Take action

  1. Stop unnecessary harvest and exposed feeding.
  2. Check actual reserves and provide appropriate internal feed when needed.
  3. Keep inspections brief and entrances defensible; use the robbing guide at the first sustained fighting.

Avoid this mistake

Do not assume every summer week is a nectar flow or feed in supers intended for a pure honey harvest.

Causes, prevention and follow-up

Common causes

Seasonal bloom gaps, drought, poor weather or limited forage.

Check the result

Review food use at least weekly during a substantial dearth, sooner for small or light colonies. Continued loss despite feeding needs a health and feeder check.

Prevent it happening again

Learn local bloom gaps and monitor hive weight between major flows.

When to get help

Ask local keepers about current forage and help for weak colonies.

Supplies and their limits

A hive top feeder provides internal feed access. Choose the actual 8 or 10 frame width, use all floats and required parts, test for leaks and follow cleaning instructions. It does not cure disease and liquid uptake depends on weather. Use an existing sound compatible feeder when possible. Remove sale honey supers from the feeding plan.

Little LaRue supplies use our own checkout.

View Little LaRue hive top feeders
Sources and review notes

Reviewed November 19, 2026. Adapt timing to local climate, weather and colony condition. A photograph or symptom list does not confirm a diagnosis.

Unsuitable feed or feeding at the wrong time

Spoiled syrup, feed not being taken, feed in harvest supers or food offered far from the cluster.

Act promptly on unsafe feed or honey contamination

Feeding must suit the colony’s need and weather. Supplemental feed is for bees, and should not become honey sold to customers.

Compare additional reference photographs

These feeding examples help identify equipment and feed access. Follow the directions for your own feeder and use feed appropriate to the weather and colony condition. Open The BeeMD reference for feeding bees (new tab).

Recognize the signs

Spoiled syrup, feed not being taken, feed in harvest supers or food offered far from the cluster.

What else can look similar?

Lack of uptake may indicate cold or a blocked feeder rather than illness; food shortage and queen trouble can coexist.

Inspect and confirm

Use feed packaging, dates, a clean container and hive notes. Check smell, cleanliness, feeder access and whether sale honey supers are present.

Your next step

Remove contaminated or fermented feed without spilling it.

Take action

  1. Remove contaminated or fermented feed without spilling it.
  2. Use plain suitable bee feed and a clean compatible feeder; ask a mentor about concentration and timing for your aim.
  3. Keep supplemental feed away from honey intended for harvest, and document any affected frames.

Avoid this mistake

Do not feed unknown honey, brown sugar, molasses or chemical additives as a guessed treatment.

Causes, prevention and follow-up

Common causes

Wrong feed, poor storage, unsuitable weather, inaccessible placement or unnecessary feeding.

Check the result

Check access and uptake within a few days. If bees do not use sound reachable feed in suitable weather, assess colony strength and queen status.

Prevent it happening again

Mix clean feed in manageable amounts, store it properly and label hive feeding dates.

When to get help

Seek help if bees are starving, feed has contaminated a harvest or repeated refusal is unexplained.

Supplies and their limits

A hive top feeder provides internal feed access. Choose the actual 8 or 10 frame width, use all floats and required parts, test for leaks and follow cleaning instructions. It does not cure disease and liquid uptake depends on weather. Use an existing sound compatible feeder when possible. Remove sale honey supers from the feeding plan.

Little LaRue supplies use our own checkout.

View Little LaRue hive top feeders
Sources and review notes

Reviewed November 19, 2026. Adapt timing to local climate, weather and colony condition. A photograph or symptom list does not confirm a diagnosis.

A leaking feeder and syrup in the hive

Wet bottom boards, syrup running down boxes, sticky ground, drowned bees or entrance fighting after feeding.

Act now to stop drowning and robbing

Leaked feed can drown bees, wet brood and attract thieves. Remove the source of the spill first.

Compare additional reference photographs

These feeding photographs are equipment references. Inspect your own feeder for the actual leak; a photograph of another feeder does not establish its fit or safety. Open The BeeMD reference for feeding bees (new tab).

Recognize the signs

Wet bottom boards, syrup running down boxes, sticky ground, drowned bees or entrance fighting after feeding.

What else can look similar?

Condensation is usually water rather than sticky sweet liquid; rain follows a different path. Check the timing of filling.

Inspect and confirm

Use a veil, gloves and a clean tray. Examine the feeder seal and orientation outside the hive using water when appropriate; keep spilled syrup away from bees.

Inspection walkthrough and additional checks

Check the feeder before returning it

  1. Remove or isolate the leaking feeder without spilling more feed onto bees. Cover spilled or exposed syrup so other colonies cannot reach it.
  2. Away from bees, inspect seams, plugs, lids and gaskets. Test the assembled feeder over a tray according to its design; some inverted feeders depend on an airtight seal and will drip if that seal fails.
  3. Check that its supporting surface is level and the correct size. Replace a damaged part with the compatible component rather than using an uncertain sealant where feed will touch it.
  4. Use a small initial fill after repair, check for leakage promptly and watch the entrance for fighting. A repeat leak means removing that feeder from use.
Your next step

Remove or stop filling the faulty feeder and clean exposed spills.

Take action

  1. Remove or stop filling the faulty feeder and clean exposed spills.
  2. Replace or repair the seal according to its design and confirm the stand is stable and level as required.
  3. Refit only after a controlled leak test; preserve food access with another suitable method if the colony is light.

Avoid this mistake

Do not use random sealants on food contact surfaces or leave the colony open while repairing.

Causes, prevention and follow-up

Common causes

Cracks, poor seals, tilted equipment, overfilling or an incorrectly installed feeder.

Check the result

Check for fresh leakage and fighting the same day. A continued leak means the feeder should stay out of service.

Prevent it happening again

Test new feeders before use and check after each refill.

When to get help

Ask a mentor about wetted brood, severe drowning or ongoing robbing.

Supplies and their limits

A hive top feeder provides internal feed access. Choose the actual 8 or 10 frame width, use all floats and required parts, test for leaks and follow cleaning instructions. It does not cure disease and liquid uptake depends on weather. Use an existing sound compatible feeder when possible. Remove sale honey supers from the feeding plan.

Little LaRue supplies use our own checkout.

View Little LaRue hive top feeders
Sources and review notes

Reviewed November 19, 2026. Adapt timing to local climate, weather and colony condition. A photograph or symptom list does not confirm a diagnosis.

Bees drowning in a feeder

Repeated floating bees, missing floats or ladders, or bees trapped under a lid.

Act promptly and correct access

A feeder needs safe access to feed and a way out. A few deaths may occur, but ongoing drowning means the design or installation needs attention.

Compare additional reference photographs

Compare access to feed and escape surfaces, then inspect your own feeder. Dead bees in syrup can reflect leakage, trapping or other problems. Open The BeeMD reference for feeding bees (new tab).

Recognize the signs

Repeated floating bees, missing floats or ladders, or bees trapped under a lid.

What else can look similar?

Dead bees may have died before entering the feeder; compare fresh losses and inspect access.

Inspect and confirm

Wear a veil and use the actual feeder instructions. Check that floats or ladders fit, move freely and provide access at the current fill level.

Your next step

Stop using a feeder with heavy ongoing losses.

Take action

  1. Stop using a feeder with heavy ongoing losses.
  2. Clean it and restore the correct compatible escape or floating parts.
  3. Refill cautiously and observe whether bees can reach feed and leave safely.

Avoid this mistake

Do not substitute materials that sink, foul feed or block access.

Causes, prevention and follow-up

Common causes

Wrong parts, overfilling, warped floats or gaps in bee access barriers.

Check the result

Check promptly after refilling and again the next day. Continued drowning requires a different safe feeder or hands on assessment.

Prevent it happening again

Inspect floats and barriers before every feeding season and refill.

When to get help

Get help if bees are too weak to climb or the colony is losing many adults.

Supplies and their limits

The correct floats help bees stand while feeding. Match the specific feeder and 5, 8 or 10 frame size and verify movement before refilling. Floats cannot fix a cracked feeder or weakness preventing bees from climbing. Cleaning or correctly refitting sound existing parts may suffice.

Little LaRue supplies use our own checkout.

View compatible replacement floats
Sources and review notes

Reviewed November 19, 2026. Adapt timing to local climate, weather and colony condition. A photograph or symptom list does not confirm a diagnosis.

Pollen bound brood nest

Large pollen areas occupying former brood cells with little empty drawn comb.

Monitor and confirm loss of laying room

A pollen bound nest has excessive pollen stored where the queen would otherwise lay. Pollen is necessary food; do not remove it solely because it is abundant.

Compare before you act

Useful pollen stores

Pollen near brood, with suitable empty drawn comb still available for the queen.

Next check
Keep the food and inspect the whole nest. A close-up of pollen is not proof of harmful crowding.

Review the pollen reference
Possible pollen crowding

Several brood-nest frames have so much stored pollen that suitable laying space is restricted.

Next check
Map pollen, eggs, brood and empty cells before moving anything. Get help rearranging frames while keeping brood together.

Follow pollen-crowding steps
Little pollen available

Limited incoming pollen and stored protein, assessed with the season and brood demand.

Next check
Review forage and colony condition before deciding whether supplemental protein is appropriate.

Check for a pollen shortage
Compare additional reference photographs

Look for stored pollen occupying cells where the queen needs laying space. A frame containing pollen is normal and does not by itself establish a pollen bound brood nest. Open The BeeMD reference for pollen- or honey-bound colony (new tab).

Recognize the signs

Large pollen areas occupying former brood cells with little empty drawn comb.

What else can look similar?

Normal pollen bands around brood are expected. Honey bound cells are filled with nectar or honey rather than colored packed pollen.

Inspect and confirm

With a veil and light, map food and brood on both faces of frames. Confirm eggs, queen history and whether other usable drawn comb is available.

Your next step

Verify that lack of laying space is the actual limitation.

Take action

  1. Verify that lack of laying space is the actual limitation.
  2. Ask a mentor to rearrange compatible frames or provide usable comb without chilling brood.
  3. Retain sufficient pollen near the nest and check for swarm preparation.

Avoid this mistake

Do not scrape pollen from occupied comb or discard all protein stores.

Causes, prevention and follow-up

Common causes

Forage pattern, colony arrangement and reduced laying can alter food distribution.

Check the result

Compare new egg placement at the next suitable inspection. No improvement requires checking queen performance and season as well as space.

Prevent it happening again

Observe food distribution during inspections, especially in small colonies.

When to get help

Seek a mentor for frame moves and an inspector for abnormal brood.

Supplies and their limits

A matching box and frames may provide room, but foundation must be drawn before it becomes usable comb. Match width, box depth and frame depth; adding space is not complete swarm control. Correcting an existing frame arrangement with a mentor may avoid buying another box.

Little LaRue supplies use our own checkout.

Check equipment fit before buying
Sources and review notes

Reviewed November 19, 2026. Adapt timing to local climate, weather and colony condition. A photograph or symptom list does not confirm a diagnosis.

Honey bees on a wooden frame during an open Langstroth hive inspection.

For the love of the bees.

The more you notice, the more there is to love. Explore practical guides to colony life, hive inspections and your first season of beekeeping.

Spend a little time in the hive